• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors are worn out with time and require to be replaced. When replacing them, it is essential that the new handles match the dimensions of the handle that was previously used.

The top screw position the lever, and the keyhole dimensions are the three measurements you have to determine. Use the size guide to help you.

Inline Lever/Lever

A lever handle or lever is a modern door handle that is designed to fit new or replacement doors. This kind of handle is available in various designs and finishes. This handle is offered by several manufacturers, including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles of uPVC/Composite are constructed of tough materials and are perfect for doors with multiple points that require a robust design. The handles are inline and they use the same spindle and screws to secure them. They can be easily installed on a new or existing uPVC/Composite door.

The handle can be placed and angled to accommodate the needs of all users. The handle has been endurance-tested to 200,000 cycles. This ensures that the quality of finish and performance is maintained over time. The lever that springs is adjustable to fit a wide range of locks. This is particularly beneficial in doors with smaller door frames where the cylinder is further back. A lever that is shorter is a good choice for doors where the latch could be activated by the thumb turn located on the inside.

Lever Pad

The lever pad upvc handle is different from the lever handles that are commonly found on doors. These handle types can either use a single spindle (inline) or independently from both sides using two inline or offset spindles (pad). They are typically employed on UPVC double glazed doors and are available in a variety of variations and styles.

The handles have been tested to a minimum of 200 000 cycles and are available in several finishes like White, Silver, Chrome & Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high degree of durability and performance for its intended use.

All UPVC handle lever pads include a spindle and screws, and can be fitted on a uPVC door. The 211mm backplate fixing centres allow for a wider handle, which is often a benefit in replacing a defective or worn multi-point door lock mechanism. These handle levers are also spring-loaded, thereby solving the issue of door handles sagging out of the horizontal position when they are not in use.

It is crucial to ensure that the PZ dimensions for both the multipoint lock and the uPVC doors when choosing the replacement UPVC spindle and handle. This measurement may also be referred to as 'handle centres' or cylinder centres'. It is important to match the correct handles.

After you have determined the correct size of PZ and the correct PZ size, you must make sure that the push and lever pads are shaped to fit the American with Disabilities Act compliant handles you require for your patio door handle with lock. They are usually a square or round shape, with an internal lever and external push pad.

The majority of UPVC Lever Pads that we sell are sprung. This means they can be reverted to a horizontal position after not in use instead of hanging and possibly being stuck in the frame. This stops draughts and cold air from getting into a house. The majority of UPVC lever pad style handles are available in left and right handed versions that allow them to be installed on either side of the doors.

Euro Cylinder

Cylinder locks can be found on uPVC and other kinds of doors. They operate by using a key that unlock a cylinder case that is then revealed with pins that can be aligned with those inside the lock body, allowing them to turn an revolving cam, opening the aluminium door handle. Euro cylinders can be equipped with up to six pins, with external and internal doors usually requiring different levels of security.

The selection of a cylinder is vital. It is based on the amount of use your doors and handles receive. external door handles euro lock doors, for instance should be equipped with cylinders with greater security while internal doors can be secured with a standard cylinder. Certain cylinders are equipped with additional features that can improve security, such as anti drill or anti bump properties.

A euro cylinder needs to be properly measured to ensure it's the right size for your door. The cylinder needs to be measured from the screw hole in the center to the ends of the cylinder. This includes the thumb turn, if there is one. It is best to do this while the lock is in place however when this isn't feasible, you can take it off and remove it to take measurements. It is crucial to avoid having a extension of the cylinder beyond the handle or escutcheon. This can make it vulnerable to snapping lock attacks.

The majority of modern cylinders have been constructed with anti-drill and bump resistance features that are built into their design. These features are designed to minimize the chances of an attack by forcing the cylinder rotate in a different direction. This can help deflect the attack and protect your doors.

Some cylinders are designed to withstand snapping. This is a common occurrence on cylinders. A specially designed tool is used to break the break line of the lock and then the front of the cylinder is snapped off. This is a lot faster and less difficult than opening the aluminium door handles with multipoint locks and leaves no evidence of a break-in, which can impede the insurance claim.

Spring Cassette

The spring cassette is positioned inside the base of the door handle backplate providing a sprung solution to return the multipoint lock handles back to their original position after use. The handles were previously equipped with no spring and would drop when the locking mechanism was removed. The addition of this simple element is one of the best ways to correct this and it is also an excellent way to stop your doors made of upvc from getting stuck in the open or closed position, as these aren't always easy to close manually.

The spring cassettes were made to be used with sprung multipoint locks. They will not fit unsprung handles, and you will have to cut a hole into the backplate to allow them to fit. (Please look at the image for a detailed diagram). These cassettes are a solution to damaged or missing cassettes in the backplate of uPVC door handles. They are supplied in one unit. They come with a square cut out that accommodates an 8mm shaft.

These spring cassettes are a fantastic value for money solution to the issue of handles on your doors sagging. They are easy to fit and will increase the lifespan of your uPVC doors. Contact us to learn more about our selection of uPVC accessories and spares. We are always available to offer expert advice and support you.